How high should a shower diverter be?

Again, there is no set height for the water controls. Take into consideration whether the controls work the tub and shower, since you’ll want to mount them lower to accommodate tub users. For shower-only controls, between 36 and 48 inches from the floor is common.

Industry standards place the showerhead at an average of 80 inches high, or 6 feet, 8 inches, but it can be higher or lower based on your preference. Diverter controls, when not on the tub spout, should be set just above the controls that turn on the water. This applies to both showers and shower-tub combinations.

Similarly, what height should a shower bar be? Shower Grab Bars should be mounted 33”-36” | 84-91 cm above the shower floor.

Consequently, what is the rough in height for a shower valve?

In a shower only unit, the faucet is placed higher at 48 inches off the floor. The shower head normally is located 72 to 80 inches above the finished floor. If the homeowner prefers an adjustment in heights, then the shower head can be roughed-in higher or lower.

How high above the floor are tub shower valves installed?

“The tub spout will generally be located 4 inches above the rim of the tub. In a shower only unit, the faucet is placed higher at 48 inches off the floor.

Where do you mount a shower valve?

The lower crosspiece, which will hold the shower valve, may be around 50 inches from the floor for a shower enclosure and lower for a bathtub — just enough to clear the lip of the tub by a few inches. The top crosspiece, which supports the showerhead, may be 76 inches above the floor in a typical installation.

What is spout reach?

Spout reach is measured from the center of the spout base horizontally out to the water stream. Spout height is measured from the sink/countertop surface vertically up to the highest point. Refer to the specification sheet for your faucet for specific measurements.

How high should shower head be mounted?

The industry standard for the height of a shower head is 80 inches above the floor of the bath. This is 6 feet, 8 inches, which is suitable for most people of average height, and even usable for those who are taller.

What is a shower valve?

A shower valve performs two basic functions, it controls the temperature and the flow of the water in your shower. It controls the temperature by mixing hot and cold water from your hot and cold water supplies in different proportions and generally has a single control to do this with.

Does a shower need a 2 inch drain?

Keep in mind that shower drains are made to fit a 2-inch drainpipe. A 2-inch pipe is the recommended pipe size because showers have a low threshold for flooding, and a 2-inch pipe helps the water drain faster than does a 1 1/2-inch pipe.

How thick does a shower wall need to be?

Most construction of bathroom walls around the shower or tub area is based on 2×4 studs so total wall thickness may well reach 5 inch thick total, at least the walls that contain waste and water supply pipes.

Should shower head be centered?

Nothing says that it needs to be perfectly centered, but many people prefer it to be. Bottom line, it’s your house, your money. Being over towards the doorway a little makes it easier to turn it on and adjust before you enter the shower.

How do you change a shower valve?

To replace a shower valve, start by unscrewing the shower handle and trim plate, so you can remove them. Then, shut the water off and cut a hole in the small opening behind the trim plate, so you can reach the valve. Using needlenose pliers, remove the valve clip and pull the valve out of the wall.

How long should the tub spout pipe be?

For slip-on tub spouts, your copper pipe should be a minimum 1″ and a maximum 2-7/8″ in length, depending on the tub spout. Refer to the manufacturer’s specifications prior to purchasing and installing to ensure you have the appropriate length for your spout.

Where should a hand held shower bar be placed?

Hold the slide bar in position against the shower wall with its bottom end about 52 inches above the tub floor. (That placement allows you to adjust the showerhead from about 52 inches to 76 inches high, which will accommodate most people.)